Frequently Asked Questions
What are dust control sticky mats and how do they help reduce contamination?
Dust control sticky mats are adhesive floor mats designed to capture dust, dirt and fine debris from footwear and trolley wheels. Positioned at entrances or transition points, they help reduce the amount of tracked-in contamination reaching clean rooms, laboratories, healthcare facilities, food processing areas, construction zones and other sensitive workplaces.
How do I set up and use a sticky mat?
Secure the pad to a clean, dry hard floor at the entry point, then remove the top protective film to expose the first adhesive sheet. Follow these steps:
- Clean and dry the floor: Clean the area where the mat will sit and allow it to dry so the self-adhesive backing can grip.
- Remove the underside liner: Peel the release liner from the underside of the pad to expose the adhesive base.
- Position and secure the pad: Place the mat at the entry point and press it down firmly from the centre outwards so it lies flat.
- Expose the first sticky sheet: Remove the clear protective film from the top to reveal the first adhesive layer, numbered 30.
- Peel away used sheets: Once the exposed layer becomes dirty or stops gripping, lift its numbered corner tab and peel it away to reveal a fresh layer underneath.
- Replace the finished pad: Continue through the numbered layers from 30 down to 1. Replace the pad once the final layer, numbered 1, has been used.
How do the 30 peel-away adhesive layers on Richmond sticky mats work?
Each Richmond sticky mat pad contains 30 individual adhesive polyethylene sheets. Once the exposed sheet has collected dust and debris, peel it away using the numbered corner tab to reveal a fresh adhesive surface underneath. The sheets count down from 30 to 1, making it easy to monitor the remaining layers and see when a replacement pad is needed.
What size sticky mat should I choose for my doorway or work area?
Richmond Dust Control Sticky Mats are available in 600 x 900mm, 660 x 1150mm and 900 x 900mm sizes. The 600 x 900mm mat is a compact option for smaller access points, while the longer 660 x 1150mm mat provides increased contact area along the direction of travel. The 900 x 900mm mat provides wider coverage across the entrance. Measure the available floor space and check where footwear and trolley wheels will pass before selecting a size.
Where should sticky mats be positioned for effective dust and dirt control?
Position sticky mats at entrances and transition points where people or wheeled equipment move from dusty or general work areas into cleaner or more sensitive environments. Examples include clean room entrances, laboratories, food production areas, healthcare facilities, server rooms and transitions between construction zones and finished areas. Place the mat directly in the traffic path so footwear and trolley wheels contact the adhesive surface.
Can Richmond sticky mats capture dust and debris from both footwear and trolley wheels?
Yes. Richmond Dust Control Sticky Mats have an adhesive surface designed to capture loose dust, dirt and fine debris from shoes, work boots and trolley wheels as they pass over the pad. Their low-profile design supports pedestrian and trolley movement through access points. Choose a size that covers the wheel paths as well as the route taken by staff.
How often should the top adhesive layer of a sticky mat be peeled away?
Peel away the exposed layer when it becomes dirty or stops gripping effectively. How often this is needed depends on pedestrian and trolley traffic, surrounding dust levels and workplace conditions. Lift the numbered corner tab to remove the used sheet and expose a fresh adhesive layer underneath. Replace the complete pad after the final sheet, numbered 1, has been used.
Do Richmond Dust Control Sticky Mats require a separate mat frame or holder?
No. Richmond sticky mats have a self-adhesive backing that secures the pad directly to a suitable clean hard floor without requiring a separate frame or holder. Clean and dry the floor before installation, remove the underside release liner, then press the pad firmly into position from the centre outwards so it lies flat.
Should I purchase an individual sticky mat pad or a carton of 10 pads?
An individual pad is a useful option for a single entrance, occasional replacement or trying the format at a new access point. A carton of 10 pads suits facilities with multiple entrances or ongoing replacement requirements. Each pad contains 30 peel-away adhesive sheets, giving 300 sheets per carton. Individual pads and cartons are available in all three sizes.
Dust Control Sticky Mats & Clean Room Sticky Mats
Richmond supplies sticky mats for capturing dust, dirt and fine debris from footwear and trolley wheels at clean room entrances, laboratories, healthcare facilities and construction access points. These adhesive floor mats collect loose particles through contact with their exposed surface, helping reduce the amount carried into the next work area.
The range includes 600 x 900mm, 660 x 1150mm and 900 x 900mm formats. Every polyethylene pad contains 30 numbered peel-away adhesive sheets and has a self-adhesive backing for installation on a clean hard floor.
All three sizes are available as individual pads or cartons of 10 pads. Choose the dimensions around your entrance layout, then select the pack quantity to match the number of access points and replacement requirements.
Sticky Floor Mats for Entrances & Transition Areas
Sticky floor mats help control dirt transfer where people and trolleys move between work areas. On a construction site, this may be the route from a dusty work zone into a finished corridor. In a laboratory or clean room, it may be a designated entrance where footwear and wheels pass over an adhesive surface before proceeding.
Measure the clear floor area and check the direction of travel before choosing a mat. The 660 x 1150mm format offers a longer contact area, while the 900 x 900mm format offers wider coverage. Position the pad where shoes and trolley wheels will make contact with the exposed sheet.
Product Types by Application
600 x 900mm Dust Control Sticky Mats
The 600 x 900mm Dust Control Sticky Mat (SMR001) is the smallest format in the range. Supplied as one pad with 30 peel-away sheets, it provides adhesive coverage for doorways and access points with limited floor space.
The 600 x 900mm Dust Control Sticky Mat Carton (SMR002) contains 10 pads of the same size. Choose this pack for multiple smaller entrances or replacement stock for an existing dust control routine.
660 x 1150mm Dust Control Sticky Mats
The 660 x 1150mm Dust Control Sticky Mat (SMR003) is the longest format in the range. Its 1150mm dimension provides a longer contact area when positioned along the direction of pedestrian and trolley travel.
The 660 x 1150mm Dust Control Sticky Mat Carton (SMR004) supplies 10 pads, each with 30 sheets. Select this pack for several transition points or regular replacement requirements using the longer format.
900 x 900mm Dust Control Sticky Mats
The 900 x 900mm Dust Control Sticky Mat (SMR005) provides a square adhesive surface. Its 900mm width offers greater coverage across an access path than the 600mm or 660mm width of the rectangular options.
The 900 x 900mm Dust Control Sticky Mat Carton (SMR006) contains 10 pads for multiple entrances or ongoing replacements. Check the usable doorway width and trolley wheel paths before selecting this format.
How to Choose Sticky Mats
Choose the dimensions first, then the pack quantity. Every pad contains 30 sheets, so the main differences between the options are floor coverage and the number of pads supplied.
| Mat size | Pad | 10-pad carton | Best for |
|---|---|---|---|
| 600 x 900mm | SMR001 | SMR002 | Limited floor space |
| 660 x 1150mm | SMR003 | SMR004 | Longer contact area |
| 900 x 900mm | SMR005 | SMR006 | Wider coverage |
- Measure the floor area: Check that the full mat fits at the chosen entrance or transition point.
- Check the traffic route: Position the mat where footwear and trolley wheels will contact the adhesive sheet.
- Plan replacement stock: Choose individual pads for single access points or 10-pad cartons for multiple entrances and ongoing use.
- Prepare the surface: Clean and dry the hard floor before securing the self-adhesive base.
Sticky Mat Features
30 Numbered Peel-Away Adhesive Sheets
Each pad contains 30 adhesive polyethylene sheets. The first usable sheet is numbered 30, with the layers counting down to the final sheet numbered 1.
Lift the numbered corner tab to remove a dirty sheet and expose a fresh adhesive surface. The numbering helps staff track the remaining layers and plan pad replacements.
Adhesive Surface for Footwear & Trolley Wheels
The exposed sheet captures loose dust, dirt and fine debris through contact with shoes, work boots and trolley wheels.
At laboratory entrances, construction transitions and other access points, place the pad directly in the traffic path so the adhesive surface contacts the footwear or wheels carrying the particles.
Low-Profile Polyethylene Construction
All three sizes use polyethylene sheets in a low-profile pad designed for pedestrian and trolley access points.
When the exposed sheet needs changing, staff can reveal the next adhesive layer without replacing the complete pad.
Self-Adhesive Backing
The adhesive base secures the pad directly to a clean hard floor without requiring a separate mat frame.
Remove the underside release liner, position the pad and press firmly from the centre outwards. Remove the clear top protective film once the pad is secured to expose layer 30.
Applications by Industry
- Clean rooms: Clean room sticky mats capture loose particles from footwear and trolley wheels at designated controlled-area entrances.
- Hospitals & healthcare: Individual pads provide adhesive coverage at designated sensitive-area access points, with cartons available for replacement stock.
- Laboratories: The 600 x 900mm format provides coverage at smaller entrances where floor space is limited.
- Food processing: Select from three sizes for transition points between general access and production areas.
- Construction sites: Position a pad along the route from dusty work zones into finished or occupied areas.
- Data centres & server rooms: Adhesive pads collect loose particles from footwear and trolley wheels at designated equipment-room entrances.
- Warehouses & commercial buildings: The 900 x 900mm format provides wider coverage at pedestrian and trolley access points.
Sticky Mats Across Australia
Richmond supplies sticky mats in three sizes, with individual pads and 10-pad cartons available for entrance dust control and ongoing replacements. Each pad provides 30 numbered adhesive sheets for capturing loose dirt and debris from footwear and trolley wheels.
Richmond has over 65 years of experience supplying wheels, castors and materials handling equipment across Australia.
Contact Richmond for help choosing sticky mat sizes and pack quantities for your entrances.